Difference between revisions of "Reamers"
(→Metric Hand Reamers) |
|||
| (19 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
The holy grail of framebuilder reamers for seat tubes is a solid spiral flute hand or chucking reamer. These are very hard to find in the fractional metric sizes common for seatposts. | The holy grail of framebuilder reamers for seat tubes is a solid spiral flute hand or chucking reamer. These are very hard to find in the fractional metric sizes common for seatposts. | ||
| + | ===Silva=== | ||
| − | == | + | [http://www.novacycles.com/catalog/product_info.php?cPath=74&products_id=1014 Silva Reamer] |
| − | + | expensive. | |
| + | ===Cyclus Shell Reamers=== | ||
| + | German bike specific tools. Nice. | ||
| + | |||
| + | The [http://www.biketoolsetc.com/index.cgi?id=39742361688&d=single&c=Tools&sc=CYCLUS-TOOLS,-ALL&tc=Reamers&item_id=CU-061 handle] costs $81.70 and each [http://www.biketoolsetc.com/index.cgi?id=39742361688&d=single&c=Tools&sc=CYCLUS-TOOLS,-ALL&tc=Reamers&item_id=CU-097 shell reamer] is another $47.00. Any common size is avaliable. Available throught Bike Tools Etc. | ||
| + | |||
| + | I wish that the reamer was spiral fluted and longer. A longer lead in would also be nicer. | ||
| + | |||
| + | [[Image:Cyclus-reamer-1.jpg]]<br><br> | ||
| + | [[Image:Cyclus-reamer-2.jpg]]<br><br> | ||
| + | [[Image:Cyclus-reamer-3.jpg]]<br><br> | ||
| + | ===Lifu=== | ||
| + | |||
| + | [http://www.lifu.biz:9090/showProductPage.html?point=0 Lifu Reamers] | ||
===Source for reamers=== | ===Source for reamers=== | ||
This is a good one: | This is a good one: | ||
| − | + | Mike@<br> | |
KBC Tools & Machinary<br> | KBC Tools & Machinary<br> | ||
1751 Sabre<br> | 1751 Sabre<br> | ||
| Line 27: | Line 41: | ||
(510) 654-1844<br> | (510) 654-1844<br> | ||
| − | They say that a regrind could be $24 for a chucking reamer $40 for a hand reamer, if they do not have to take too much material off. | + | They say that a regrind could be $24 for a chucking reamer $40 for a hand reamer, if they do not have to take too much material off. $55 on my job. |
| + | |||
| + | ===English Hand Reamers=== | ||
| + | |||
| + | [http://www.icscuttingtools.com ICS Cutting Tools] | ||
| + | |||
| + | [http://www.icscuttingtools.com/catalog/page_196.pdf] | ||
| + | |||
| + | ===Metric Hand Reamers=== | ||
| + | |||
| + | [http://www.metricmcc.com/ Metric & Multistandard (MMCC)] | ||
| + | |||
| + | [http://www.metricmcc.com/catalog/Ch5/5-540.pdf M&MS Catalog page 5-540] | ||
| + | |||
| + | Also: http://www.tapdie.com/html/reamers__hand_reamers__hss_met.html | ||
| + | |||
| + | |||
| + | ====From: Truls Erik Johnsen to me==== | ||
| + | |||
| + | "FYI: Tracy Tools in the UK (www.tracytools.com) have 41mm HSS Dormer branded | ||
| + | reamers at £55 plus shipping." | ||
| + | |||
| + | ===Metric Shell Reamers=== | ||
| + | 1:30 bore, ISO 2402:1972, DIN 219/B | ||
| + | |||
| + | [http://www.omalutensili.it/index.asp?l=UK Omal] | ||
| + | [http://www.omalutensili.it/dl.asp?f=OMAL-Catalogue.pdf Omal Catalog p.44] | ||
| + | |||
| + | [http://www.vidia-v.com/images/PDF%20Listovki/R_dor_en.pdf Vidia-v] Bulgaria. | ||
| + | |||
| + | [http://www.metricmcc.com/ Metric & Multistandard (MMCC)] | ||
| + | [http://www.metricmcc.com/catalog/Ch5/5-548.pdf M&MS Catalog page 5-548] | ||
| + | |||
| + | [http://www.stimtools.cz Stim Tools] | ||
| + | [http://www.stimtools.cz/kat_pdf/katalog_vyhrubniky.pdf Stim Tools Catalog p. 36] | ||
| + | |||
| + | Shell core drills? DIN 222N (ISO 3314) | ||
| + | |||
| + | |||
| + | [http://www.rotoxlt.sk/ Rotox] | ||
| + | [http://www.rotoxlt.sk/pdf/obro_04.pdf Rotox p.84] | ||
===27.2mm=== | ===27.2mm=== | ||
| Line 43: | Line 97: | ||
1-1/8: 5-13/16: 11-5/8: 5-010-155: $47.65 (28.58mm reground to 27.2 for finishing)<br> | 1-1/8: 5-13/16: 11-5/8: 5-010-155: $47.65 (28.58mm reground to 27.2 for finishing)<br> | ||
| − | [http://www.toolmex.com/Tools/TCutting.asp Toolmex] | + | I was told that [http://www.toolmex.com/Tools/TCutting.asp Toolmex] was the supplier for all of these reamers but they turned out to be sourced from [http://www.fenes.com.pl/index1.php Fenes] of Poland. [http://www.fenessaw.com/pobierz_plik2.php?n=8e296a067a25 Catalog] |
toolmex helical shell reamers may be good for the next order. | toolmex helical shell reamers may be good for the next order. | ||
5-155-030 for 1-1/16" $41.00 | 5-155-030 for 1-1/16" $41.00 | ||
| + | |||
| + | ===Bore Polishing=== | ||
| + | |||
| + | This simple tool is available for cleaning up a bore. | ||
| + | |||
| + | [[Image:Bore-polishing.jpg]] | ||
| + | |||
| + | ===Honing=== | ||
| + | |||
| + | [[Image:Hones.jpg]] | ||
[[category:Bicycle]] | [[category:Bicycle]] | ||
[[category:Frame Building]] | [[category:Frame Building]] | ||
[[category:Special Tools (Bicycle)]] | [[category:Special Tools (Bicycle)]] | ||
| + | [[category:PVD Sportbikes]] | ||
Latest revision as of 16:12, 3 May 2010
The holy grail of framebuilder reamers for seat tubes is a solid spiral flute hand or chucking reamer. These are very hard to find in the fractional metric sizes common for seatposts.
Contents
Silva
expensive.
Cyclus Shell Reamers
German bike specific tools. Nice.
The handle costs $81.70 and each shell reamer is another $47.00. Any common size is avaliable. Available throught Bike Tools Etc.
I wish that the reamer was spiral fluted and longer. A longer lead in would also be nicer.
Lifu
Source for reamers
This is a good one:
Mike@
KBC Tools & Machinary
1751 Sabre
Hayward, CA 94545
(510) 732-5500
(800) 521-1740
KBCtools.com
Sharpening and Regrinders
I'll be trying these guys at first:
Cliff @
Pacific Reamer & Cutter Service
4115 Broadway
Oakland, CA 94611
(510) 654-1844
They say that a regrind could be $24 for a chucking reamer $40 for a hand reamer, if they do not have to take too much material off. $55 on my job.
English Hand Reamers
Metric Hand Reamers
Also: http://www.tapdie.com/html/reamers__hand_reamers__hss_met.html
From: Truls Erik Johnsen to me
"FYI: Tracy Tools in the UK (www.tracytools.com) have 41mm HSS Dormer branded reamers at £55 plus shipping."
Metric Shell Reamers
1:30 bore, ISO 2402:1972, DIN 219/B
Vidia-v Bulgaria.
Metric & Multistandard (MMCC) M&MS Catalog page 5-548
Stim Tools Stim Tools Catalog p. 36
Shell core drills? DIN 222N (ISO 3314)
27.2mm
Probably the most common size seatpost in the industry for steel bikes.
Spiral Flute Chucking Reamers:
Size: Flute Length: OAL: KBC P/N: Price
1-1/16: 2-3/4: 10-1/2: 5-020-295: $37.40 (26.99mm for roughing)
1-3/32: 2-7/8: 11: 5-020-300: $37.40 (27.78mm reground to 27.2 for finishing)
Spiral Flute Hand Reamers:
Size: Flute Length: OAL: KBC P/N: Price
1-1/16: 5-5/8: 11-1/4: 5-010-150: $43.15 (26.99mm for roughing)
1-1/8: 5-13/16: 11-5/8: 5-010-155: $47.65 (28.58mm reground to 27.2 for finishing)
I was told that Toolmex was the supplier for all of these reamers but they turned out to be sourced from Fenes of Poland. Catalog
toolmex helical shell reamers may be good for the next order.
5-155-030 for 1-1/16" $41.00
Bore Polishing
This simple tool is available for cleaning up a bore.
Honing
