Difference between revisions of "Six Speed MTB"

From Pvdwiki
Jump to: navigation, search
(→‎8 speed vs. 9 speed)
(→‎Building the cassette)
 
(81 intermediate revisions by the same user not shown)
Line 1: Line 1:
−
After running a single speed mountain bike in Marin, CA for the past 4 months, I have decided that it may not be for me. It is a very interesting way to ride, but it really leaves me wanting when the terrain gets fairly steep and soft, and when the downhill gets up to real speeds. I figure that I could use a little bit of range from center to make things a little more fun while keeping my drive train solid for winter riding.
+
I have been trying to get down to only one mountain bike for a few years. For the past two, I was down to just my Intense 5.5 with a 36 Talas on the front. It's a great bike, but since I ride it so hard, and I'm so busy, I always ended up making rushed repairs just before a ride. This was not cool.
 +
 
 +
So, I put together a single speed as a back-up/winter bike. This was to reduce wear on my nice bike and reduce my workload. After running the single speed mountain bike in Marin, CA for the past 4 months, I have decided that it may not be for me. It is a very interesting way to ride, but it really leaves me wanting when the terrain gets fairly steep and soft, and when the downhill gets up to real speeds. I figure that I could use a little bit of range from center to make things a little more fun while keeping my drive train rock solid for winter riding.
  
 
While practicing for the Sea Otter Downhill race in 2006, I got to talking to a pro rider that was running a four or six speed setup. I realized that I really had to be a little more creative when thinking about what is possible when setting up a bike for specific targets. That minimal gearing setup has stuck in the back of my mind untill now. It may be perfect for what I need.
 
While practicing for the Sea Otter Downhill race in 2006, I got to talking to a pro rider that was running a four or six speed setup. I realized that I really had to be a little more creative when thinking about what is possible when setting up a bike for specific targets. That minimal gearing setup has stuck in the back of my mind untill now. It may be perfect for what I need.
Line 10: Line 12:
 
For this reason, a 27-speed mountain bike really only has about 12 or 15 correct gear choices. Other choices may be possible, but result in such a horrible chain line as to be inefficent or destructive. A 1X9 is really just a 5 speed with 4 additional gears that are completely destructive or inefficent to use.
 
For this reason, a 27-speed mountain bike really only has about 12 or 15 correct gear choices. Other choices may be possible, but result in such a horrible chain line as to be inefficent or destructive. A 1X9 is really just a 5 speed with 4 additional gears that are completely destructive or inefficent to use.
  
−
So, we go down to 1X6. A 1X5 is probably better in terms of pure theory, but since I can fit six speeds on my hub, I am going to try it. With either of these setups, the chain is only shifted between 2 or 3 cogs from center, keeping a fairly efficent chain line. This also keeps chain wear down to a minimum.
+
So, we go down to 1X6. A 1X5 is probably better in terms of pure theory, but since I can fit six speeds on my hub, I am going to try it. With either of these setups, the chain is only shifted between 2 (8.7mm) or 2.5 (10.9mm) cogs from center, keeping a fairly efficent chain line. This also keeps chain wear down to a minimum. A 1X9 would end up 4 (17.4mm) cogs from center.
 +
 
 +
Once I can get a 10 speed MTB shifter (XTR 2008?), I will try to go to seven speeds. That makes a cassette just a tiny bit wider that 6 speeds with a 9 speed space. If I can get away with using 9 speed cogs, I will just have to make up some 2.17mm (0.0855") spacers.
 +
 
 +
::{| border="3"
 +
|+ '''Maximum Chain Deflection<br>Assumes Centered Chain Line'''
 +
! # of Gears !! 7 Speed Spacing !! 8 Speed Spacing !! 9 Speed Spacing !! 10 Speed Spacing
 +
|-
 +
! 1
 +
| 0.0mm || 0.0mm || 0.0mm || 0.0mm ||
 +
|-
 +
! 2
 +
| 2.50mm || 2.40mm || 2.17mm || 1.98mm ||
 +
|-
 +
! 3
 +
| 5.00mm || 4.80mm || 4.34mm || 3.95mm ||
 +
|-
 +
! 4
 +
| 7.50mm || 7.20mm || 6.51mm || 5.93mm ||
 +
|-
 +
! 5
 +
| 10.0mm || 9.60mm || 8.68mm || 7.90mm ||
 +
|-
 +
! 6
 +
| 12.50mm || 12.00mm || 10.85mm || 9.88mm ||
 +
|-
 +
! 7
 +
| 15.00mm || 14.40mm || 13.02mm || 11.85mm ||
 +
|-
 +
! 8
 +
| N/A || 16.80mm || 15.19mm || 13.83mm ||
 +
|-
 +
! 9
 +
| N\A || N/A || 17.36mm || 15.80mm ||
 +
|-
 +
! 10
 +
| N\A || N/A || N/A || 17.78mm ||
 +
|}
 +
 
 +
An interesting artical on this topic has been written by [http://www.hw.ac.uk/mecwww/research/mdk/res.htm Matt D. Kidd, N. E. Loch, R. L. Reuben].
 +
 
 +
Also, [http://www.bhpc.org.uk/HParchive/PDF/hp50-2000.pdf James B. Spicer,* Christopher J.K. Richardson, Michael J. Ehrlich and Johanna R. Bernstein].
 +
 
 +
Even [http://www.machinehead-software.co.uk/bike/gears/gearing_diagram.html#sprocket_alignment software] has been developed for figuring things out.
  
 
===The Hub===
 
===The Hub===
−
While any cassette hub can be used for doing this, one hub is really better than all the rest. The [[Hadley Hubs|Hadley Single Speed Disc hub]]. This is one of the finest hubs availble in terms of quality and configurations, but it has some other things going for it that are perfect for this project.
+
While ANY standard cassette hub can be used for doing this, one hub is really better than all the rest. The [[Hadley Hubs|Hadley Single Speed Disc hub]]. This is one of the finest hubs availble in terms of quality and configurations, but it has some other things going for it that are perfect for this project. Another good option is the [http://www.profileracing.com/products_home.php?productid=52 Profile 6-Speed Disc hub]. It will also fit six 8-speed cogs. A Chris King SS will only fit four.
  
 
*Wider flanges than a standard cassette hub. This makes the wheel laterally stronger.
 
*Wider flanges than a standard cassette hub. This makes the wheel laterally stronger.
Line 22: Line 67:
  
 
I had done some research about how many gears I could fit on this hub before I spent the money on parts. I was pretty positive that I would be able to fit five speeds on this hub. I even spoke directly with Mike Hadley, the hubs namesake. He said five. When I went to assemble my cassette on the hub, I found that I could in fact fit six, 9-speed spaced, 9-speed width cogs on the cassette.
 
I had done some research about how many gears I could fit on this hub before I spent the money on parts. I was pretty positive that I would be able to fit five speeds on this hub. I even spoke directly with Mike Hadley, the hubs namesake. He said five. When I went to assemble my cassette on the hub, I found that I could in fact fit six, 9-speed spaced, 9-speed width cogs on the cassette.
 +
 +
Hub info:
 +
:*Diameter of Hub at spoke hole circle: 59mm (Now 60mm)
 +
:*Right (drive side) center of hub to flange: 33.2mm
 +
:*Left(brake side) center of hub to flange 33.2mm
 +
:*Diameter of individual spoke holes: 2.5mm
  
 
===8 speed vs. 9 speed===
 
===8 speed vs. 9 speed===
Line 28: Line 79:
 
The advantage to an 8-speed configuration is that the chain and sprockets are slightly more robust that with the nine. Shifting tends to be slightly better as well since it takes a lot more disruption to derail the chain on an 8 speed setup.
 
The advantage to an 8-speed configuration is that the chain and sprockets are slightly more robust that with the nine. Shifting tends to be slightly better as well since it takes a lot more disruption to derail the chain on an 8 speed setup.
  
−
The advantage to a 9-speed configuration is that 9-speed chains and sprockets are far more available than 8-speed parts. This applys to shifters as well, a very important consideration.
+
The advantage to a 9-speed configuration is that 9-speed chains and sprockets are far more available than 8-speed parts. This applys to shifters as well, a very important consideration. Most importantly though, given the same number of gears, the 9-speed spacing keeps a better chain line.
  
 
In the end, I decided to go with a 9-speed configuraion since I try to source my bikes parts so that I can go into any bike store anywhere and get replacement parts in stock and cheap. I will use a Dura-Ace 9 speed chain.
 
In the end, I decided to go with a 9-speed configuraion since I try to source my bikes parts so that I can go into any bike store anywhere and get replacement parts in stock and cheap. I will use a Dura-Ace 9 speed chain.
  
  
−
{| border="3"
+
::{| border="3"
 
|+ '''Cassette Info'''
 
|+ '''Cassette Info'''
 
! Brand !! Speed !! Cog, Ctr. to Ctr. !! Cog, Thickness !! Spacer Thickness !! Spacer ID
 
! Brand !! Speed !! Cog, Ctr. to Ctr. !! Cog, Thickness !! Spacer Thickness !! Spacer ID
Line 41: Line 92:
 
|-
 
|-
 
! Shimano
 
! Shimano
−
| 9 || 4.32mm || 1.76mm || 2.56mm || 33.6mm
+
| 9 || 4.34mm || 1.78mm || 2.56mm || 33.6mm
 
|-
 
|-
 
! SRAM
 
! SRAM
Line 50: Line 101:
 
|-
 
|-
 
! SRAM
 
! SRAM
−
| 8 || 4.80mm || 1.80mm || 2.54mm || 33.6mm
+
| 8 || 4.80mm || 1.80mm || 3.00mm || 33.6mm
 +
|-
 +
! Shimano
 +
| 7 || 5.00mm || 1.85mm || 3.15mm || 33.6mm
 
|}
 
|}
  
−
{| border="3"
+
::{| border="3"
 
|+ '''Chain Info'''
 
|+ '''Chain Info'''
 
! Brand !! Speed !! Size !! Pin Width !! Roller Width !! Roller Diameter
 
! Brand !! Speed !! Size !! Pin Width !! Roller Width !! Roller Diameter
Line 64: Line 118:
 
|-
 
|-
 
! SRAM
 
! SRAM
−
| 9 || 1/2" x 3/32"  || 6.9mm || 2.2mm || 7.75mm
+
| 9 || 1/2" x 11/128"  || 6.65mm || 2.2mm || 7.75mm
 
|-
 
|-
 
! Shimano
 
! Shimano
Line 73: Line 127:
 
|-
 
|-
 
! SRAM
 
! SRAM
−
| 7/8 || 1/2" x 3/32"  || 6.8mm || 2.2mm || 7.75mm
+
| 8 || 1/2" x 3/32"  || 7.1mm || 2.2mm || 7.75mm
 
|-
 
|-
 
! SRAM
 
! SRAM
−
| 7/8 || 1/2" x 3/32" || 7.1mm || 2.2mm || 7.75mm
+
| 7 || 1/2" x 3/32" || 6.8mm || 2.2mm || 7.75mm
 
|}
 
|}
  
Line 90: Line 144:
 
My initial cassette choice is 11,14,17,20,23,26. These will combine with a 34 tooth front sprocket to, hopefully, make some good usable gearing.
 
My initial cassette choice is 11,14,17,20,23,26. These will combine with a 34 tooth front sprocket to, hopefully, make some good usable gearing.
  
−
I broke two [http://www.sram.com/en/srammountain/cassettes/9speed/pg970.php SRAM PG-970] cassettes apart to make this stack. 11/13/15/17/20/23/26/30/34 & 11/12/14/16/18/21/24/28/32. The cassette is broken apart by removing the 1.5mm allen at the back.<br>
+
I broke two [http://www.sram.com/en/srammountain/cassettes/9speed/pg970.php SRAM PG-970] cassettes apart to make this stack. 11/13/15/17/20/23/26/30/34 & 11/12/14/16/18/21/24/28/32. The cassette is broken apart by removing the 1.5mm allen at the back. A Shimano cassette may require griding or drilling out a few rivets.<br><br>
 +
Sale price, $35 each.<br>
 
[[Image:6speed1.jpg]]<br>
 
[[Image:6speed1.jpg]]<br>
 +
The spline view and the allen screw.<br>
 
[[Image:6speed2.jpg]]<br>
 
[[Image:6speed2.jpg]]<br>
 +
Choices!!<br>
 
[[Image:6speed3.jpg]]<br>
 
[[Image:6speed3.jpg]]<br>
  
−
To use the 11 tooth cog on this cassette, about 0.036" needs to be surface ground from its integrated expanded spacer. This is because I am not using the cog that initially mated to this one. Once this is done, I can shim the cassette into postion for the best chain line and away from the spokes.<br>
+
::{| border="3"
 +
|+ '''SRAM PC970 Choices'''
 +
! Model !! 11 !! 12 !! 13 !! 14 !! 15 !! 16 !! 17 !! 18 !! 19 !! 20 !! 21 !! 22 !! 23 !! 24 !! 25 !! 26 !! 27 !! 28 !! 29 !! 30 !! 31 !! 32 !! 33 !! 34
 +
|-
 +
! 11-21
 +
| 11 || 12 || 13 || 14 || 15 || 16 || 17 || X || 19 || X || 21 || X || X || X || X || X || X || X || X || X || X || X || X || X
 +
|-
 +
! 12-21
 +
| X || 12 || 13 || 14 || 15 || 16 || 17 || X || 19 || X || 21 || X || 23 || X || X || X || X || X || X || X || X || X || X || X
 +
|-
 +
! 12-23
 +
| 11 || 12 || 13 || 14 || 15 || X || 17 || X || 19 || X || 21 || X || 23 || X || X || X || X || X || X || X || X || X || X || X
 +
|-
 +
! 12-26
 +
| X || 12 || 13 || 14 || 15 || X || 17 || X || 19 || X || 21 || X || 23 || X || X || 26 || X || X || X || X || X || X || X || X
 +
|-
 +
! 11-32
 +
| 11 || 12 || X || 14 || X || 16 || X || 18 || X || X || 21 || X || X || 24 || X || X || X || 28 || X || X || X || 32 || X || X
 +
|-
 +
! 11-34
 +
| 11 || X || 13 || X || 15 || X || 17 || X || X || 20 || X || X || 23 || X || X || 26 || X || X || X || 30 || X || X || X || 34
 +
|}
 +
 
 +
 
 +
To use the 11 tooth cog on this cassette and 9 speed spacing, about 0.036" needs to be surface ground from its integrated expanded spacer. This is because I am not using the cog that initially mated to this one. This is also necessary with a Shimano cassette.
 +
 
 +
For 8 speed spacing, instead of grinding the cog, an approximately 0.010" shim washer will be added to it. Peskey little details that bikes work really good.<br>
  
 
[[Image:6speed4.jpg]]<br><br>
 
[[Image:6speed4.jpg]]<br><br>
 +
The surface ground cog. This cog is not usable without doing this.<br>
 +
[[Image:6speed12.jpg]]<br><br>
  
 
This is what the cassette looks like (11 tooth cog not modified yet):<br>
 
This is what the cassette looks like (11 tooth cog not modified yet):<br>
 
[[Image:6speed6.jpg]]<br>
 
[[Image:6speed6.jpg]]<br>
 +
 +
It seems that the center of the cassette stack makes for a rear chainline of 52mm, a fairly common measure for singlespeed MTBs. Pay attention to the chain line section.<br>
 +
Note that the stack looks fairly straight. This was done for an even distribution of gears. For better shifting on the smaller cogs, I would have placed smaller gaps at that end.<br>
 
[[Image:6speed7.jpg]]<br>
 
[[Image:6speed7.jpg]]<br>
 +
 +
[[Image:Sixxer3.jpg]]<br>
  
 
===Shifters===
 
===Shifters===
Line 107: Line 197:
  
 
Just for fun, I figured that I would try a [http://bike.shimano.com/media/cycling/techdocs/en/bikecomponents/SL/SI-6LH0A_v1_m56577569830567074.pdf Shimano Saint] (SL-M800) shifter for this project.
 
Just for fun, I figured that I would try a [http://bike.shimano.com/media/cycling/techdocs/en/bikecomponents/SL/SI-6LH0A_v1_m56577569830567074.pdf Shimano Saint] (SL-M800) shifter for this project.
 +
 +
I'm not exaclty happy with the ergonomics of the Saint shifter. It is very out of the way, which is nice, but it is kind of hard to get at when the going gets rough. I will try chainging it's position again, then switch to a Deore LX or Sram X-7 shifter.
 +
 +
The saint shifter gets in the way in this configuration. When postion was changed, It is very out of the way, but too much. It is very hard to downshift on the fly.<br>
 +
[[Image:6speed17.jpg]]
  
 
===Derailures===
 
===Derailures===
  
 
While any standard MTB derailure will work, I am choosing to run a short cage derailure since I will have only one front ring. The road rear derailures by shimano work just fine in the dirt.  
 
While any standard MTB derailure will work, I am choosing to run a short cage derailure since I will have only one front ring. The road rear derailures by shimano work just fine in the dirt.  
−
[http://bike.shimano.com/media/cycling/techdocs/en/bikecomponents/RD/SI-5VN0A_v1_m56577569830563515.pdf Shimano 105 Rear Derailleur RD-5600-SS]
+
[http://bike.shimano.com/media/cycling/techdocs/en/bikecomponents/RD/SI-5VN0A_v1_m56577569830563515.pdf Shimano 105 Rear Derailleur RD-5600-SS]. Shimano was my main choice for rear derailure since any Shimano road derailure is cross compatable with 9-spd mtb shifters and cassette spacing. This is an economy thing. I want to be able to use the most common parts available if I end up in a jam.
 +
 
 +
The 10spd 105 derailure limit screws were 'just' out of range for practical purposes. I had to swap screws.
 +
 
 +
[[Image:6speed13.jpg]]<br>
 +
[[Image:6speed14.jpg]]<br>
 +
[[Image:6speed15.jpg]]<br>
 +
I ordered some specific size screws so that I can make this look more pro, but this is it for now.<br>
 +
[[Image:6speed16.jpg]]<br>
  
−
If I had gone the SRAM route, I would have chosen the new [http://www.sram.com/en/srammountain/components/x9/rearderailleur.php 2007 X-9 Short Cage] derailure.
+
::''Option''
 +
::If I had gone the SRAM route, I would have chosen the new [http://www.sram.com/en/srammountain/components/x9/rearderailleur.php 2007 X-9 Short Cage] derailure.
  
−
Important note: SRAM road parts are not cross compatable with the off road line. Do not try to use a SRAM road rear derailure.
+
::Important note: SRAM road parts are not cross compatable with the off road line. Do not try to use a SRAM road rear derailure.
  
 
===Chain Guides===
 
===Chain Guides===
  
−
A chain guide may or may not be necessary to keep the chain in place up front. A riding test will confirm what has to be done. This may be an important issue.
+
A chain guide is necessary to keep the chain in place up front. This is an important issue.<br>
 +
 
 +
[[Image:Guide8.jpg]]<br>
 +
 
 +
===Chain Line===
 +
 
 +
Aparently, the defacto standard for Singlespeed MTB chainline is 52mm. This is good because the Hadley cassette body seems perfectly centered about that if running a five speed drivetrain.
 +
 
 +
Standard front chain lines for 3 ring mtb are either 47.5mm or 50mm. For road (2 ring), track, and bmx, chainline is generally 43.5mm. Shimano Saint 150 uses a 57.5 chainline and Shimano DXR uses a 44mm chainline, all the rest of the HollowTech II MTB cranksets use a 50mm chainline.
 +
 
 +
I endeded up with a 45.8mm front chain line with a 113mm Shimano UN-73 bottom bracket and a [http://www.whiteind.com/ENO_Products/cranks.html White Industries ENO Crankset]. This sucked. I really needed to bring the chainline out to about 51.5 to 52.0mm for the system to work best. For this reason, no spacers are used on the back side of the cassette.<br><br>
 +
[[Image:6speed8.jpg]]<br><br>
 +
 
 +
I had to change cranks to get my bike at least ready for a real test ride. Using a cheap Shimano Hollowtech crank with a chainring in the outermost postition and the same 113mm bottom bracket, I was able to get a usable chainline at about 51.5mm. I ordered a 122.5 and a 127.5mm bottom bracket so that I can use my lighter White Industies cranks. This probably means going to a Shimano UN53 bb, or a [http://www.fullspeedahead.com/fly.aspx?layout=product&taxid=60&pid=80 FSA]<br><br>
 +
[[Image:6speed9.jpg]]<br><br>
 +
I fine tuned my cassette position by using a single Shimano 1mm 10 speed cassette shim behind the cassette. That's all the room I had. This picture shows the difference between that shim and a standard 2.5mm spacer.<br>
 +
[[Image:6speed71.jpg]]<br><br>
 +
The chain is almost perfectly centered on the cassette, just a touch toward the lower gears.<br>
 +
[[Image:6speed10.jpg]]<br><br>
 +
 
 +
I may end up using a Shimano HollowTech II crank with the new external type BB on this bike when the [http://bike.shimano.com/media/cycling/techdocs/en/bikecomponents/FrontDriveSystem/SI-6JXFE_v1_m56577569830572774.pdf LX] cranks start going on sale. All Shimano HollowTech II MTB cranks have a 50mm chain line. This may reqire a shift to five speed to center the rear chain line.
 +
 
 +
:'''Note:''' I am starting to think that I need to bias my chainline more toward the lower gears. I spend very little time in the 11 tooth cog and spend quite a bit of time in my two lowest gears while climbing. A 50mm chain line may make more sense after all. The 11 tooth is critical at times, but only for a very small percentage of the ride.
  
 
===Results===
 
===Results===
  
−
Project is not complete.
+
'''Ride #1'''<br>
 +
As I rushed to get the chain line prepared in time for our regular Tuesday night ride, the weather developed into one of the biggest storms of the year so far. This was going to be a hell of a shake down ride: One of the shortest days of the year, in the dark, gail force winds, and blinding rain.
 +
 
 +
[[Image:6speed11.jpg]]<br><br>
 +
 
 +
The bike worked flawlessly. The only thing I needed to do on the trail was tighten the headset.
 +
 
 +
The chain never even hinted at coming off the chainring, but to be honest, we were not getting up to such a speed in these conditions to really give the system a true test. It did work this time, though. That is a good sign.
 +
 
 +
The bike is similar to a singlespeed in terms of not having every gear option available, so a little pushing and spinning is involved, but it is so much nicer on climbs and especially on decents. Just more comfortable, faster, and more flexible.
 +
 
 +
'''Ride #2'''<br>
 +
Changed the gearing to 11,14,17,20,24,28. Shifting worked fine and the lower gears were nicer.
 +
 
 +
Big problem...Chain came off. Fast stuff caused it to drop. Definately will need a chain retention device. I will make one.
 +
 
 +
Starting to think that six speeds is a bit much for a single front ring. I may have to go down to five speeds. I will need an even longer bottom bracket to do this. I have ordered a 122.5 and a 127.5 so that I can play  around and see what works.
 +
 
 +
'''Ride #3'''<br>
 +
Chainged the gearing to 11,14,17,20,24,30. This seems to be the absolue limit of he short cage derailure. I would have rathered a 25 instead of the 24, or a 29 instead of the 30, but I didn't have any from the cassettes I broke apart.
 +
 
 +
Did a great vacation poach on Mt. Tam. Big climb, super single track. the gearing is perfect. Really fun, but still work. Dropped the chain once, but I have come to terms with the fact that I need a chain guide. Really snappy feeling.
 +
 
 +
[[Image:Sixxer.jpg]]<br><br>
 +
 
 +
[[Image:Sixxer2.jpg]]<br><br>
  
 +
'''Ride #4'''<br>
  
 +
A Tamarancho loop. Dropped a chain once again, but I was able to chase some fast fully geared guys both up and down the hill even after giving them a handicap. So, it works. All I need now are some parts and some time in the machine shop to make a chain guide.
  
 +
'''Ride #5'''<br>
  
 +
Chain guide installed. It works perfectly.
  
 +
I may want to go up to a 36 tooth ring up front so that I can stop using the 11 tooth cog. A 36 tooth ring with a 12-15-18-21-25-32 cassette may be in order, but i will have to sub out the 25 for either a 24 or 26 since SRAM does not make one.<br>
  
 +
[[Image:Finished-six-speed.jpg]]
  
 
[[category:bicycle]]
 
[[category:bicycle]]
 
[[category:drivetrain (Bicycle)]]
 
[[category:drivetrain (Bicycle)]]

Latest revision as of 20:55, 23 February 2007

I have been trying to get down to only one mountain bike for a few years. For the past two, I was down to just my Intense 5.5 with a 36 Talas on the front. It's a great bike, but since I ride it so hard, and I'm so busy, I always ended up making rushed repairs just before a ride. This was not cool.

So, I put together a single speed as a back-up/winter bike. This was to reduce wear on my nice bike and reduce my workload. After running the single speed mountain bike in Marin, CA for the past 4 months, I have decided that it may not be for me. It is a very interesting way to ride, but it really leaves me wanting when the terrain gets fairly steep and soft, and when the downhill gets up to real speeds. I figure that I could use a little bit of range from center to make things a little more fun while keeping my drive train rock solid for winter riding.

While practicing for the Sea Otter Downhill race in 2006, I got to talking to a pro rider that was running a four or six speed setup. I realized that I really had to be a little more creative when thinking about what is possible when setting up a bike for specific targets. That minimal gearing setup has stuck in the back of my mind untill now. It may be perfect for what I need.


Why 1X6 instead of 1X9

Like most things drivetrain, it comes down to chain line. When I am helping a new rider learn to shift properly, one key rule that I give them is to keep their chain as straight as possible. A straight chain is one of the most efficient drive systems available for a bicycle. A straight chain is one of the factors that make a single speed bike feel quite like it does.

For this reason, a 27-speed mountain bike really only has about 12 or 15 correct gear choices. Other choices may be possible, but result in such a horrible chain line as to be inefficent or destructive. A 1X9 is really just a 5 speed with 4 additional gears that are completely destructive or inefficent to use.

So, we go down to 1X6. A 1X5 is probably better in terms of pure theory, but since I can fit six speeds on my hub, I am going to try it. With either of these setups, the chain is only shifted between 2 (8.7mm) or 2.5 (10.9mm) cogs from center, keeping a fairly efficent chain line. This also keeps chain wear down to a minimum. A 1X9 would end up 4 (17.4mm) cogs from center.

Once I can get a 10 speed MTB shifter (XTR 2008?), I will try to go to seven speeds. That makes a cassette just a tiny bit wider that 6 speeds with a 9 speed space. If I can get away with using 9 speed cogs, I will just have to make up some 2.17mm (0.0855") spacers.

Maximum Chain Deflection
Assumes Centered Chain Line
# of Gears 7 Speed Spacing 8 Speed Spacing 9 Speed Spacing 10 Speed Spacing
1 0.0mm 0.0mm 0.0mm 0.0mm
2 2.50mm 2.40mm 2.17mm 1.98mm
3 5.00mm 4.80mm 4.34mm 3.95mm
4 7.50mm 7.20mm 6.51mm 5.93mm
5 10.0mm 9.60mm 8.68mm 7.90mm
6 12.50mm 12.00mm 10.85mm 9.88mm
7 15.00mm 14.40mm 13.02mm 11.85mm
8 N/A 16.80mm 15.19mm 13.83mm
9 N\A N/A 17.36mm 15.80mm
10 N\A N/A N/A 17.78mm

An interesting artical on this topic has been written by Matt D. Kidd, N. E. Loch, R. L. Reuben.

Also, James B. Spicer,* Christopher J.K. Richardson, Michael J. Ehrlich and Johanna R. Bernstein.

Even software has been developed for figuring things out.

The Hub

While ANY standard cassette hub can be used for doing this, one hub is really better than all the rest. The Hadley Single Speed Disc hub. This is one of the finest hubs availble in terms of quality and configurations, but it has some other things going for it that are perfect for this project. Another good option is the Profile 6-Speed Disc hub. It will also fit six 8-speed cogs. A Chris King SS will only fit four.

  • Wider flanges than a standard cassette hub. This makes the wheel laterally stronger.
  • Zero dish. Since the flanges are centered on the hub, the spokes will be evenly tensioned. This is good.
  • Long cassete body. Given that the flange width is maximized, by also maximizing the cassette body length gives us the maximum possibilities for gearing.

6speed5.jpg

I had done some research about how many gears I could fit on this hub before I spent the money on parts. I was pretty positive that I would be able to fit five speeds on this hub. I even spoke directly with Mike Hadley, the hubs namesake. He said five. When I went to assemble my cassette on the hub, I found that I could in fact fit six, 9-speed spaced, 9-speed width cogs on the cassette.

Hub info:

  • Diameter of Hub at spoke hole circle: 59mm (Now 60mm)
  • Right (drive side) center of hub to flange: 33.2mm
  • Left(brake side) center of hub to flange 33.2mm
  • Diameter of individual spoke holes: 2.5mm

8 speed vs. 9 speed

One of the decisions that needed to be made when assembling the needed parts for this project was weather it would be a 8-speed or 9-speed chained and spaced setup.

The advantage to an 8-speed configuration is that the chain and sprockets are slightly more robust that with the nine. Shifting tends to be slightly better as well since it takes a lot more disruption to derail the chain on an 8 speed setup.

The advantage to a 9-speed configuration is that 9-speed chains and sprockets are far more available than 8-speed parts. This applys to shifters as well, a very important consideration. Most importantly though, given the same number of gears, the 9-speed spacing keeps a better chain line.

In the end, I decided to go with a 9-speed configuraion since I try to source my bikes parts so that I can go into any bike store anywhere and get replacement parts in stock and cheap. I will use a Dura-Ace 9 speed chain.


Cassette Info
Brand Speed Cog, Ctr. to Ctr. Cog, Thickness Spacer Thickness Spacer ID
Shimano 10 3.95mm 1.60mm 2.35mm 33.6mm
Shimano 9 4.34mm 1.78mm 2.56mm 33.6mm
SRAM 9 4.34mm 1.80mm 2.54mm 33.6mm
Shimano 8 4.80mm 1.80mm 3.00mm 33.6mm
SRAM 8 4.80mm 1.80mm 3.00mm 33.6mm
Shimano 7 5.00mm 1.85mm 3.15mm 33.6mm
Chain Info
Brand Speed Size Pin Width Roller Width Roller Diameter
Shimano 10 1/2" x 11/128" 5.9mm  ??mm 7.75mm
Shimano 9 1/2" x 11/128" 6.6mm 2.2mm 7.75mm
SRAM 9 1/2" x 11/128" 6.65mm 2.2mm 7.75mm
Shimano 7/8 IG 1/2" x 3/32" 7.1mm 2.2mm 7.75mm
Shimano 7/8 HG 1/2" x 3/32" 7.3mm 2.2mm 7.75mm
SRAM 8 1/2" x 3/32" 7.1mm 2.2mm 7.75mm
SRAM 7 1/2" x 3/32" 6.8mm 2.2mm 7.75mm

Building the cassette

Do not attempt to make a cassette using a stack of single speed cogs. That is not only expensive, but will result in poor shifting performance. Modern cassetts have a complicated array of ramps and shapes to help the chain move about the cluster. When we make a 6 speed cassette, we will have larger jumps between gears, increasing our need for shifting help.

It is best to canibalize a constructed cassette for this. When choosing what cassettes to canibalize for this project, you mainly need to focus on whether it is 8 or 9 speed and that it is possible to break apart. Lots of the higher end cassets will be built around a carrier, these will not be suitable.

If you take some time and do a little math and some thinking, you can get a good idea of what gears or range you will need for your cassette. Although I did do this, in the end, I built the widest range I could given my six choices.

Remember that rear derailure choice defines the largest possible cog on the cassette. Since I am building with a Shimano 105 short cage derailure, I needed to keep my max sprocket to 27 teeth or less.

My initial cassette choice is 11,14,17,20,23,26. These will combine with a 34 tooth front sprocket to, hopefully, make some good usable gearing.

I broke two SRAM PG-970 cassettes apart to make this stack. 11/13/15/17/20/23/26/30/34 & 11/12/14/16/18/21/24/28/32. The cassette is broken apart by removing the 1.5mm allen at the back. A Shimano cassette may require griding or drilling out a few rivets.

Sale price, $35 each.
6speed1.jpg
The spline view and the allen screw.
6speed2.jpg
Choices!!
6speed3.jpg

SRAM PC970 Choices
Model 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
11-21 11 12 13 14 15 16 17 X 19 X 21 X X X X X X X X X X X X X
12-21 X 12 13 14 15 16 17 X 19 X 21 X 23 X X X X X X X X X X X
12-23 11 12 13 14 15 X 17 X 19 X 21 X 23 X X X X X X X X X X X
12-26 X 12 13 14 15 X 17 X 19 X 21 X 23 X X 26 X X X X X X X X
11-32 11 12 X 14 X 16 X 18 X X 21 X X 24 X X X 28 X X X 32 X X
11-34 11 X 13 X 15 X 17 X X 20 X X 23 X X 26 X X X 30 X X X 34


To use the 11 tooth cog on this cassette and 9 speed spacing, about 0.036" needs to be surface ground from its integrated expanded spacer. This is because I am not using the cog that initially mated to this one. This is also necessary with a Shimano cassette.

For 8 speed spacing, instead of grinding the cog, an approximately 0.010" shim washer will be added to it. Peskey little details that bikes work really good.

6speed4.jpg

The surface ground cog. This cog is not usable without doing this.
6speed12.jpg

This is what the cassette looks like (11 tooth cog not modified yet):
6speed6.jpg

It seems that the center of the cassette stack makes for a rear chainline of 52mm, a fairly common measure for singlespeed MTBs. Pay attention to the chain line section.
Note that the stack looks fairly straight. This was done for an even distribution of gears. For better shifting on the smaller cogs, I would have placed smaller gaps at that end.
6speed7.jpg

Sixxer3.jpg

Shifters

Shifters define the indexing of the rear derailure. Your shifter must match your choice of 8 or 9-speeds.

Just for fun, I figured that I would try a Shimano Saint (SL-M800) shifter for this project.

I'm not exaclty happy with the ergonomics of the Saint shifter. It is very out of the way, which is nice, but it is kind of hard to get at when the going gets rough. I will try chainging it's position again, then switch to a Deore LX or Sram X-7 shifter.

The saint shifter gets in the way in this configuration. When postion was changed, It is very out of the way, but too much. It is very hard to downshift on the fly.
6speed17.jpg

Derailures

While any standard MTB derailure will work, I am choosing to run a short cage derailure since I will have only one front ring. The road rear derailures by shimano work just fine in the dirt. Shimano 105 Rear Derailleur RD-5600-SS. Shimano was my main choice for rear derailure since any Shimano road derailure is cross compatable with 9-spd mtb shifters and cassette spacing. This is an economy thing. I want to be able to use the most common parts available if I end up in a jam.

The 10spd 105 derailure limit screws were 'just' out of range for practical purposes. I had to swap screws.

6speed13.jpg
6speed14.jpg
6speed15.jpg
I ordered some specific size screws so that I can make this look more pro, but this is it for now.
6speed16.jpg

Option
If I had gone the SRAM route, I would have chosen the new 2007 X-9 Short Cage derailure.
Important note: SRAM road parts are not cross compatable with the off road line. Do not try to use a SRAM road rear derailure.

Chain Guides

A chain guide is necessary to keep the chain in place up front. This is an important issue.

Guide8.jpg

Chain Line

Aparently, the defacto standard for Singlespeed MTB chainline is 52mm. This is good because the Hadley cassette body seems perfectly centered about that if running a five speed drivetrain.

Standard front chain lines for 3 ring mtb are either 47.5mm or 50mm. For road (2 ring), track, and bmx, chainline is generally 43.5mm. Shimano Saint 150 uses a 57.5 chainline and Shimano DXR uses a 44mm chainline, all the rest of the HollowTech II MTB cranksets use a 50mm chainline.

I endeded up with a 45.8mm front chain line with a 113mm Shimano UN-73 bottom bracket and a White Industries ENO Crankset. This sucked. I really needed to bring the chainline out to about 51.5 to 52.0mm for the system to work best. For this reason, no spacers are used on the back side of the cassette.

6speed8.jpg

I had to change cranks to get my bike at least ready for a real test ride. Using a cheap Shimano Hollowtech crank with a chainring in the outermost postition and the same 113mm bottom bracket, I was able to get a usable chainline at about 51.5mm. I ordered a 122.5 and a 127.5mm bottom bracket so that I can use my lighter White Industies cranks. This probably means going to a Shimano UN53 bb, or a FSA

6speed9.jpg

I fine tuned my cassette position by using a single Shimano 1mm 10 speed cassette shim behind the cassette. That's all the room I had. This picture shows the difference between that shim and a standard 2.5mm spacer.
6speed71.jpg

The chain is almost perfectly centered on the cassette, just a touch toward the lower gears.
6speed10.jpg

I may end up using a Shimano HollowTech II crank with the new external type BB on this bike when the LX cranks start going on sale. All Shimano HollowTech II MTB cranks have a 50mm chain line. This may reqire a shift to five speed to center the rear chain line.

Note: I am starting to think that I need to bias my chainline more toward the lower gears. I spend very little time in the 11 tooth cog and spend quite a bit of time in my two lowest gears while climbing. A 50mm chain line may make more sense after all. The 11 tooth is critical at times, but only for a very small percentage of the ride.

Results

Ride #1
As I rushed to get the chain line prepared in time for our regular Tuesday night ride, the weather developed into one of the biggest storms of the year so far. This was going to be a hell of a shake down ride: One of the shortest days of the year, in the dark, gail force winds, and blinding rain.

6speed11.jpg

The bike worked flawlessly. The only thing I needed to do on the trail was tighten the headset.

The chain never even hinted at coming off the chainring, but to be honest, we were not getting up to such a speed in these conditions to really give the system a true test. It did work this time, though. That is a good sign.

The bike is similar to a singlespeed in terms of not having every gear option available, so a little pushing and spinning is involved, but it is so much nicer on climbs and especially on decents. Just more comfortable, faster, and more flexible.

Ride #2
Changed the gearing to 11,14,17,20,24,28. Shifting worked fine and the lower gears were nicer.

Big problem...Chain came off. Fast stuff caused it to drop. Definately will need a chain retention device. I will make one.

Starting to think that six speeds is a bit much for a single front ring. I may have to go down to five speeds. I will need an even longer bottom bracket to do this. I have ordered a 122.5 and a 127.5 so that I can play around and see what works.

Ride #3
Chainged the gearing to 11,14,17,20,24,30. This seems to be the absolue limit of he short cage derailure. I would have rathered a 25 instead of the 24, or a 29 instead of the 30, but I didn't have any from the cassettes I broke apart.

Did a great vacation poach on Mt. Tam. Big climb, super single track. the gearing is perfect. Really fun, but still work. Dropped the chain once, but I have come to terms with the fact that I need a chain guide. Really snappy feeling.

Sixxer.jpg

Sixxer2.jpg

Ride #4

A Tamarancho loop. Dropped a chain once again, but I was able to chase some fast fully geared guys both up and down the hill even after giving them a handicap. So, it works. All I need now are some parts and some time in the machine shop to make a chain guide.

Ride #5

Chain guide installed. It works perfectly.

I may want to go up to a 36 tooth ring up front so that I can stop using the 11 tooth cog. A 36 tooth ring with a 12-15-18-21-25-32 cassette may be in order, but i will have to sub out the 25 for either a 24 or 26 since SRAM does not make one.

Finished-six-speed.jpg

Retrieved from "http://peterverdone.com/wiki/index.php?title=Six_Speed_MTB&oldid=4014"